Skip to content

Measure Tool ​

Quick Answer ​

The Measure tool lets you drop a series of points on the map and read back the distance between them as a straight line (as the crow flies). Where Drive time is enabled for your environment, you can also measure driving time along roads. Turn it on from the Measure distance button in the desktop chat bar, click the map to place points, and read the per-segment and total distance in the on-map readout. A measurement is temporary -- it is never saved and disappears when you close the tool.

Turning It On ​

The Measure distance button (a ruler / straighten icon) sits in the desktop chat bar right after Traffic, before Create map report. Click it to start a measure session; click it again to close.

  • The tool is available on the desktop map. It is not offered in Street View, where no line can be placed.
  • Measuring and drawing a shape use the same on-map engine and cannot run at the same time. If you start Measure while a shape draw or edit is in progress, Zeus.ai shows the message "Finish or exit shape drawing before measuring." Finish or cancel the shape first, then measure.

When the tool is active, a compact bar appears at the bottom center of the map with the controls (and, where Drive time is enabled, the mode toggle), and a readout card appears above it once you place your first point.

Placing a Line ​

  1. Click Measure distance to open the tool. The hint reads "Click the map to start".
  2. Click the map to drop the first point, then keep clicking to add more points. Each click adds a segment from the previous point.
  3. While you are drawing, the hint reads "Click to add · Enter to finish" (or "Click to add · Enter for drive times" in Drive time mode). Press Enter to finish the line.
  4. After the line is finished, the hint reads "Drag points to adjust". Drag any point to move it; the distances update automatically.

Controls in the Measure Bar ​

  • Straight line / Drive time -- switches between the two measurement modes (see below). This toggle only appears where Drive time is enabled; otherwise the bar measures straight-line distance only.
  • Undo -- removes the last point you placed (available while you are still drawing).
  • Clear -- removes the whole line so you can start over.
  • Close (the x, or press Esc) -- exits the tool. Closing discards the measurement.

Straight-Line Distance ​

In Straight line mode (the default), the readout lists each segment and a Total, all in miles. This is the direct point-to-point distance, ignoring roads -- useful for quick "how far apart are these two spots" checks, trade-area radius sanity checks, or spacing between candidate sites.

While you are still drawing, a Next segment row previews the distance from your last point to the cursor.

Drive Time ​

Availability

Drive time is turned off in most environments right now while routing is moved to a new service, so you will usually see straight-line measuring only. If the Straight line / Drive time toggle does not appear in the measure bar, the tool measures straight-line distance only.

Switch to Drive time mode to measure driving time and driving distance along real roads instead of a straight line.

  • Drive times are calculated for a finished line, so place your points and press Enter to see results.
  • Each segment row shows the driving time and driving distance together, for example "12 min · 8.4 mi", and the Total sums them.
  • The driving route is drawn on the map so you can see the path each segment follows.
  • A short notice under the total explains anything the route could not resolve.

If a segment cannot be routed, its row shows one of:

  • No route -- there is no drivable path between those two points.
  • Unavailable -- the routing service could not return a result for that segment.
  • Retrying… -- the request is being retried; the value fills in when it completes.

Segments still being calculated show a brief loading indicator, and the total waits until every segment is ready before showing a combined time and distance. If any segment ends up as No route or Unavailable, the total shows a dash (—) instead of a combined value.

Tips ​

  • Use straight-line for radius and spacing checks, drive time for accessibility. Straight-line answers "how far apart," while drive time answers "how long to get there" along the road network.
  • Adjust without starting over. After finishing a line, drag any point to refine it -- the distances (and, in Drive time mode, the route) recompute automatically.
  • The measurement is disposable. Nothing is saved. To keep a boundary or trade area, draw a shape instead of measuring.

SiteZeus Location Intelligence Platform — powered by Zeus.ai